Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Temple City, CA
Gate installation in Temple City usually means working with a 1940s or 1950s ranch home on a deep setback lot, where the original wrought-iron driveway gate has finally outlived its hinges. Most calls we get are for replacements and full-system upgrades, not just repairs. The hot San Gabriel Valley summers and occasional winter rains push wood and iron gates through hard cycles, and by the time a gate leans or drags, the posts and hardware usually need a full reset. Call (855) 679-6795 for a free estimate. We answer 24/7 with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Temple City Homes Are Different
Temple City’s 91780 is built around post-WWII ranch homes from the 1940s and 1950s. Many of these properties still carry their original or second-generation driveway gates and wrought-iron fencing. That shapes the work here. Gate repair in Temple City is often about restoring decades-old swing gates and their aging hinges, posts, and latches rather than installing new automated systems on brand-new builds.
The deep front setbacks and mature camphor and ficus street trees create a specific failure pattern. Gate posts sit in shade on the north-facing side, so iron hinges there rust from dampness while the sun-baked south side dries and cracks. Wood swing gates warp unevenly for the same reason. Long concrete driveways mean a dragging gate scrapes for yards before anyone notices, chewing up both the gate and the concrete. And the clay-heavy soils under many Temple City lots swell with winter rain, settling posts just enough to throw a gate out of square.
Santa Ana wind episodes add another layer. Dry summer heat loosens hinge screws and latch hardware, and a good gust can twist a gate that was barely hanging on. None of this is exotic. It is what we see on Temple City service calls week after week.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Temple City Services
Temple City homeowners call us most about two things: a gate that no longer hangs or latches right, and an electric system that stopped responding. Here is how each works.
Gate Repair in Temple City
Temple City’s vintage swing gates fail in predictable ways. Hinges pull loose from sun-dried posts, latch bars stop meeting the strike plate, and wood panels warp until they bind against the ground or the frame. On iron gates, rust at the bottom rail is the usual culprit. A repair here typically means realigning the gate, replacing hinge hardware, resetting or replacing a post if the clay soil has let it settle, and welding cracks when the gate is iron. Gate Repair in Temple City covers the full mechanical side for residential swing and slide gates. Most jobs are quoted on the first visit and completed the same day.
Electric Gate Repair in Temple City
On the automated side, Temple City gate systems fail most often at the control board, the loop detector, or the operator motor. Many of these systems were added long after the original gate went in, so wiring runs along fence lines and through garden beds where moisture and shifting ground take their toll. Electric Gate Repair in Temple City covers motors, remote systems, safety edges, and control boards. We diagnose the brand-specific fault the first visit, whether it is a LiftMaster opener or a Viking board, instead of throwing parts at the problem.
Gate Installation in Temple City
Gate installation in Temple City usually starts with a gate that has reached the end of its service life or a homeowner who wants automated entry on a driveway that never had it. On the 1940s and 1950s ranch properties throughout 91780, the original posts are often still in the ground but too worn to hold a new gate. Replacing a gate properly here means evaluating the posts and hinges before anything gets hung, because the clay-heavy soil settles and the deep setbacks mean a gate that drags will scrape a long stretch of concrete. When the job calls for it, we pull the old posts, set new ones to proper footing depth, hang the gate, and run the automation. Gate Installation covers the full process from measure to final adjustment.
Automatic Gate Installation
Signs you need it
You are opening and closing the gate by hand every day, or you have an old operator that is loud, slow, or no longer responding to remotes.
What it costs in Temple City
Automatic gate installation in Temple City typically runs $2,950 to $6,800 depending on gate size, operator type, and wiring distance.
How we do it
We measure the gate and approach, set or reset posts to proper footing depth, mount the operator, run the power and control wiring, install safety edges and loop detectors, and program remotes and keypads.
Driveway Gate Installation
Signs you need it
The existing driveway gate is leaning, dragging, rusted through at the rails, or no longer matches the security and look you want for the property.
What it costs in Temple City
A new driveway gate in Temple City generally lands between $1,700 and $5,200 installed, depending on width, material, and whether posts need replacement.
How we do it
We remove the old gate and hardware, check post condition and plumb, install new hinges and latch hardware, hang the gate, and adjust for a clean swing or slide with no dragging.
Sliding Gate Installation
Signs you need it
The driveway slopes toward the gate or the gate swings out over the sidewalk, and a sliding panel would be safer and more practical for the property.
What it costs in Temple City
Sliding gate installation in Temple City typically runs $3,200 to $7,400 for a complete system with track, motor, and safety sensors.
How we do it
We build the proper track base, set the track and posts, hang the sliding panel on rollers, install the operator and safety edges, and test the full cycle until it runs smooth.
What Gate Installation Costs in Temple City
| Item | Typical range in Temple City |
|---|---|
| Driveway gate installation | $1,700 – $5,200 |
| Automatic gate installation | $2,950 – $6,800 |
| Sliding gate installation | $3,200 – $7,400 |
These are typical installed ranges for Temple City’s ranch-era lots. The final number moves with gate width, material choice, post condition, and how far the power run has to go.
How long does a gate installation take in Temple City?
Most Temple City gate installations finish in one day when posts are reused. If we are pulling old posts and setting new ones in clay-heavy soil, allow a second day for concrete to cure before the gate is hung.
Do I need a permit to install a gate in Temple City?
Most cities require a permit for new gate posts, footings, or electrical work on an automated system. Call Temple City’s building department to confirm what your project needs. The written estimate we give before work starts spells out the full scope.
Brands We Service in Temple City
We work on the brand already on your Temple City property. That includes Linear and Mighty Mule openers on residential driveways, DoorKing systems on multi-unit and commercial entry points, and Viking and Ghost Controls on estates and ranches. Our brands coverage means we diagnose the fault the first visit and carry the common boards, remotes, and safety parts for same-day fixes.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Temple City, CA
| Service | Typical range in Temple City |
|---|---|
| Gate repair (hinge, latch, realignment) | $180 – $480 |
| Gate post replacement | $750 – $1,500 |
| Weld repair, iron gate | $250 – $650 |
| Control board replacement | $450 – $1,100 |
| Operator motor replacement | $600 – $1,600 |
| Loop detector replacement | $350 – $800 |
| Photo eye or safety sensor replacement | $180 – $400 |
| Remote or keypad programming | $80 – $220 |
| Driveway gate installation | $1,700 – $5,200 |
| Automatic gate installation | $2,950 – $6,800 |
| Sliding gate installation | $3,200 – $7,400 |
What pushes price up in Temple City is mostly the condition of what is already there: settled posts in clay soil, rusted hinge plates, and long power runs from the house to a gate sitting deep on the lot. Every job gets a written estimate before work starts, so the price you see is the price you approve.
Neighborhoods We Serve in Temple City
We cover all of Temple City, from the older ranch blocks east of Temple City Boulevard to the newer infill builds tucked between them. Response time is quick across 91780 because we dispatch from the San Gabriel Valley, not from across the county.
- North Temple City
- East Temple City
- The area around Temple City Park
- South Temple City off Las Tunas Drive
- The blocks west of Rosemead Boulevard
Service Area – Cities Near Temple City
Our service area reaches Temple City and the surrounding San Gabriel Valley communities. If you are in San Gabriel, CA, Monrovia, CA, Baldwin Park, CA, or West Puente Valley, CA, we can schedule a gate estimate with the same team that handles Temple City calls.
Serving Temple City, CA – Our Local Coverage Area
We serve Temple City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Company in Temple City
We dispatch from the San Gabriel Valley, so most Temple City calls get a same-day visit when the request comes in before late afternoon. Call (855) 679-6795. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Some Temple City neighborhoods have HOA design rules covering gate height, material, and finish. Your association office or property manager can confirm before you commit. We install to your spec and will note any HOA requirements on the written estimate.
Yes. The same team handles mechanical gate work and electric operator repair, so a Temple City call that starts as a leaning gate can also resolve a failing opener in the same visit. Call (855) 679-6795 for a free estimate.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within the hour.
- 4You approve before work beginsNothing starts until you say go.
What Temple City Customers Say
"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Rosa Hernandez"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Paul Fletcher"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Raj Sharma